An order was placed for one of our 2D Compact Model Bell's for the Mike Rigby Ringing Centre in Warkwickshire.

The model features a red frame with a red-sallied bell rope.

Completed October 2026

An order was placed for one of our 2D Compact Model Bell's for the ringing chamber at St. James' Church, Horton, Glos.

The model features a blue frame with a green-sallied bell rope.

Completed October 2026

An order was placed for one of our 2D Compact Model Bell's for the ringing chamber at Holy Trinity Church, Wickwar, Glos.

The model features a red frame with a blue-sallied bell rope.

Completed October 2026

The tower houses a Tubular Chime of 8 bells in C#. And a singular 5cwt bell in C, hung for stationary chiming.

An order was placed for a USB Belfry Camera to be installed.

Completed September 2026

A project was placed for a new portable micro-ring of 3. The bells are fully-ringable and has been made to be taken to shows & events to promote English church bell ringing.

All three bells are cast-aluminium, and the tenor is gold-coated. The Tenor weighs 2.1oz (59.5g) and the peal has been tuned to the key of B♭ Major.

The bells are hung on 3D-Printed headstocks and swing on steel gudgeons. The frame is also 3D-Printed, and also the wheels and clappers.

The ring is setup on a tripod so it can be easily be setup & dismantled. It can also be adjusted in height so it can be rung sat down or standing up.

Completed September 2026

We have manufactured a portable desktop scaled set of tower tubular bells.

This desktop set is a scaled down replica of our tower tubular bells that we manufacture and install in belfries, and is playable via an Ellacombe apparatus.

Due to a delay is getting the project started, the bells were manufactured and tuned back in early 2024. The project restarted in June 2026.

All 8 bells have a diameter of 1.00". The tenor has a length of 17.36", weighs 4.13oz and is tuned to the key of G.

The bells are suspended in an aluminium frame and are chimed via stainless-steel hammers with a nylon-insert. The hammers are operated via a mini Ellacombe chime apparatus situated in front of the setup using a pulley-sytem to swing them over to the bells. The frame has a handle fitted on top for easy carrying.

Completed July 2026

This is our first handbell we have produced.

The bell was specially cast for this project. The brass bell was cast in 2025. It has a diameter of 70mm (2.76"), weighs 5.63oz (159.5g) and has been tuned to G#.

The bell is mounted to a 3D-Printed PLA handle and is fitted with a clapper consisting of braided-polyester and a wooden ball to give the bell a nice mellow tone.

Completed May 2026

This is a 10lb mini-ring of 6 bells in E.

A project was placed for a bourdon bell to be installed for the mini-ring. A specified bell was cast for this project. The bell was cast in December 2025. It has a diameter of 19.00", weighs 0-1-5 (33lbs), and hums the note A.

The bell is hung on a counter-balanced aluminium headstock for slow-swing ringing, with a flying counter-balanced clapper. The bell is lever-swung. The bell is hung in a timber bell-frame and its gudgeons are on ball-bearings.

Completed February 2026

We have hung our spare bell for swing-chime and will be used as a portable display until we find it a new home.

We acquired this bell in 2023 from Benfield Bells who refurbished it in 2022. It has a diameter of 13", weighs 0-1-1 (29lbs) and is tuned to F#.

The bell is mounted to a timber headstock with stainless steel straps, and swings on ball bearings. Its cast-in staple has been reused for its new composite-shafted clapper. The bell is hung in a timber bell-frame.

Completed November 2025

This famous 800 year old house contains a lot of historic artifacts.

We were approached by the owner of the house to refurbish this Victorian railway carriage lamp which was found in very poor condition.

We disassembled the lamp into its separate parts, all metal parts were sand-blasted clean from corrosion. The large holes that were created from corrosion were filled in, then it was all painted up with a zinc-based paint for extra protection.

Completed November 2025

In December 2023 we took over the production of Mr. Hartley's famous 2D wooden model bell. Following his passing in January 2026, we strive to continue his legacy and keep his ingenious design going.

Keeping the same flat 2D design but using modern technology, we have given it a face-lift with some design improvements. Featuring a new frame design, they are now 3D Printed, swings on ball bearings, has a rope-stay & hook, and features a more realistic bell rope.

See in the "Accessories" page for further details & contact us to place an order.

Completed September 2025

This is a 10lb mini-ring of 6 bells in E.

Manufacturing & installation of Ellacombe hammers and a baton-clavier to the mini-ring

We manufactured & fitted composite Ellacombe hammers under each bell of the mini-ring. The strings are attached to a timber baton-clavier on the wall so an individual ringer can play the bells like a keyboard.

Completed June 2025

Refurbishment of a baldrick clapper.

This baldrick clapper was found underground in a private owner's garden. The owner asked if we would like to keep it. We have given it a full refurbishment. All iron-work was sand-blasted clean, then spray-painted. A new polyacetal block was CNC-Machined to specifications. A new leather-strap was measured & cut. The original rivets couldn't be salvaged, so new galvanised bolts have been used to finish the assembly of the clapper.

Completed May 2025

This tower houses a Tubular Chime of 8 bells in C#. And a 5cwt Service Bell in C, for stationary chiming.

A job was raised to repair the Ellacombe hammer on the service bell as it had seized up.

The hammer was dismantled in situ, cleaned and oiled with a special grade oil. Rebuilt, tested and working as good as new. The stopper-bolt was adjusted also.

Completed February 2024

We manufactured this lovely large display bell for the ringing chamber. 

The bell has a diameter of 9.75", weighs 15lbs 7oz, and hums the note Eb. It is hung on a powder-coated steel headstock (manufactured by O'Shea Engineering) and swings on ball bearings.

It features a counter-balanced composite-shafted clapper and is hung in a lovely pine bell-frame.

Completed July 2023

An order was placed for a new clapper for this lovely ship's bell from HMS Dulverton, which is now hung dead for chiming in the church of All Saints, Dulverton.

The new clapper is a chain clapper with an aluminium ball, and is fitted with a cotton-woven chiming rope. The clapper is mounted using the bell's cast-in staple.

Completed April 2023

Potentially the World's First 3D Printed Metal Bell has been manufactured!

This is a project we worked on for some time. The bell was designed with our own profile.  The bell was 3D printed at Apex Additive Technologies on 30th November 2022. The bell is printed out of Titanium-alloy, using the same alloy-ratio they use in aerospace! It has a diameter of 3.90" (99mm), weighs 6.20oz (0.18kg), and hums the note A (1765Hz). The bell is fitted with a 3D-Printed PLA handle, and has a plastic-shafted clapper & staple, with a wooden ball to produce a more mellow sound due to the hardness of the alloy.

Completed December 2022

The tower houses a 21cwt full-circle ring of 10 bells in Eb.

A job was raised after an Ellacombe hammer was damaged from a bell being rung-up. We removed the hammer from the frame. We sent the hammer to O'Shea Engineering to have it forged-repaired. Once returned, we refitted the hammer to the frame & carried out inspections & tests.

Completed October 2022

This is a single 17.75" steel bell, weighs 0-3-11, note C.

This is the business owner's personal steel bell. The bell was refurbished for protection from rust. The bell was then sent to O'Shea Engineering to have a resin pad cast on top. Once returned, an aluminium cube frame on wheels was manufactured to hang the bell dead for stationary chiming, and can be easily moved around to be taken to shows & events.

Completed June 2022

The tower houses a 12cwt full-circle ring of 8 bells in G.

An order was placed for the installation of PC sensor for the training bell.

And the installation of USB Belfry Camera.

Completed August 2021

The tower houses a 25cwt full-circle ring of 12 bells in D. With an extra-treble & flat 6th.

We assisted O'Shea Engineering with removing and refitting the clappers out of bells 1-9, the extra-treble and the flat-6th.

Bells 10-12 have Avon Ropes' timber-shafted clappers which swing on ball bearings.

Completed October 2020

The tower houses a 12cwt full-circle ring of 6 bells in F#.

We carried out a project of minor repairs & adjustments in the belfry to keep the bells in working order.

The work consisted of; Adjusting & tightening of clappers, new split-pins for back 5 clappers, oiling of pulley wheels, replacing bell rope top-ends with pre-stretched polyester, and reinstating the Ellacombe chimes.

Completed March 2020